Toyota Camry

1992-1997 of release

Repair and operation of the car

Toyota Camry
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
- 4. Capital repairs of engines
   4.2. General information
   4.3. Check of a compression
   4.4. Recommendations about removal of the engine
   + 4.5. Removal and installation of the engine
   4.6. Sequence of dismantling of the engine
   4.7. Dismantling of a head of the block of cylinders
   + 4.8. Cleaning and survey of a head of the block of cylinders
   4.9. Assembly of a head of the block of cylinders
   4.10. Removal of pistons with rods
   4.11. Removal of a bent shaft
   + 4.12. Block of cylinders of the engine
   4.13. Pistons and rods
   4.14. Bent shaft
   + 4.15. Survey and choice of radical and conrod bearings
   4.16. Control of a side play of assembly of the balance weight (engine 5S-FE)
   4.17. Engine balance of assembly at capital repairs
   4.18. Installation of piston rings
   + 4.19. Installation of a bent shaft and check of working gaps of bearings
   4.20. Installation of a back sealing ring of a bent shaft
   4.21. Installation of pistons and rods, check of working gaps of bearings
   4.22. Installation of assembly of the balance weight (engine 5S-FE)
   4.23. Start of the engine after capital repairs
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment

4.4. Recommendations about removal of the engine

GENERAL INFORMATION

Details of the six-cylinder V6 3MZ-FE engine (the engine 3MZ-FE is similar to the shown engine 1MZ-FE except for the oil pallet)

1 – masloslivny stopper;
2 – laying;
3 – oil pallet;
4 – partition of the oil pallet;
5 – cover of radical bearings;
6 – persistent half rings of a bent shaft;
7 – bent shaft;
8 – mesh oil filter;
9 – laying;
10 – oil pump;
11 – forward sealing ring of a bent shaft;
12 – sealing ring of round section;
13 – arm of a single pulley;
14 – bypass pipe of the cooling system;
15 – oil pressure sensor;
16 – clip;
17 – drainage hose;
18 – connector;
19 – lock ring;

20 – piston finger;
21 – spring of a piston ring;
22 – first compression ring;
23 – second compression ring;
24 – oil scraper rings;
25 – piston;
26 – top plug of a rod;
27 – rod;
28 – rod bearing;
29 – lower cover of a rod;
30 – back basic plate;
31 – flywheel;
32 – back sealing ring of a bent shaft;
33 – back cover of a bent shaft;
34 – arm of an oil filter;
35 – radical bearings;
36 – back plate;
37 – drive plate;
38 – forward plate

Main details of a chetyrekhtsa of the lindrovy engine

1 – masloslivny stopper;
2 – laying;
3 – oil pallet;
4 – mesh filter;
5 – laying;
6 – partition of the oil pallet;
7 – covers of radical bearings;
8 – persistent half rings of a bent shaft;
9 – bent shaft;
10 – laying;
11 – oil pump;
12 – forward sealing ring of a bent shaft;
13 – right suspension bracket of the power unit;
14 – elastic element of a suspension bracket;
15 – rod cover;
16 – rod bearing;
17 – rod;

18 – lock ring;
19 – piston;
20 – second compression ring;
22 – first compression ring;
23 – oil scraper piston rings;
24 – piston finger;
25 – rod plug;
26 – block of cylinders;
27 – laying;
28 – back basic plate;
29 – flywheel or plate of the drive;
30 – back sealing ring of a bent shaft;
31 – back cover of a bent shaft;
32 – radical bearings;
33 – drive plate;
34 – back plate;
35 – forward plate

If you decided to remove the engine for repair, then some preparations have to be made.

The paramount importance has the choice of the venue of works, for providing space for service and storage of spare parts. It is desirable to do it at bus station or in a garage with an equal horizontal floor with a pure hard coating.

Before removal of the engine wash up the engine and a motor compartment. Removal of the engine requires the load-lifting mechanism allowing to lift safely the power unit.

If you remove the engine for the first time, it is necessary to invite the skilled expert. Besides, there are many cases when one person cannot perform at the same time all operations at removal of the engine.