Toyota Camry

1992-1997 of release

Repair and operation of the car


Toyota Camry
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
- 4. Capital repairs of engines
   4.2. General information
   4.3. Check of a compression
   4.4. Recommendations about removal of the engine
   + 4.5. Removal and installation of the engine
   4.6. Sequence of dismantling of the engine
   4.7. Dismantling of a head of the block of cylinders
   + 4.8. Cleaning and survey of a head of the block of cylinders
   4.9. Assembly of a head of the block of cylinders
   4.10. Removal of pistons with rods
   4.11. Removal of a bent shaft
   + 4.12. Block of cylinders of the engine
   4.13. Pistons and rods
   4.14. Bent shaft
   + 4.15. Survey and choice of radical and conrod bearings
   4.16. Control of a side play of assembly of the balance weight (engine 5S-FE)
   4.17. Engine balance of assembly at capital repairs
   4.18. Installation of piston rings
   + 4.19. Installation of a bent shaft and check of working gaps of bearings
   4.20. Installation of a back sealing ring of a bent shaft
   4.21. Installation of pistons and rods, check of working gaps of bearings
   4.22. Installation of assembly of the balance weight (engine 5S-FE)
   4.23. Start of the engine after capital repairs
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment




4.22. Installation of assembly of the balance weight (engine 5S-FE)
GENERAL INFORMATION

Starting position of tags of the balance weight No. 2

Sequence of tightening of bolts of fastening of assembly of the balance weight

Provisions in which it is necessary to measure a balance weight No. 1 shaft side play in relation to a bent shaft

Definition of a side play of a shaft of the balance weight No. 1

The second and fourth situation for measurement of a side play of a shaft of the balance weight No. 1

Installation of the indicator of hour type for measurement of a side play of a shaft of the balance weight

PERFORMANCE ORDER
1. Turn a bent shaft of the engine so that the piston of the first cylinder was installed in the top dead point.
2. Establish a shaft of the balance weight No. 2 in the situation shown in the drawing the Starting position of tags of the balance weight No. 2.
3. Install assembly of the balance weight on the block of cylinders of the engine and fix by bolts, having tightened them in a certain sequence (see rice. Sequence of tightening of bolts of fastening of assembly of the balance weight).
4. As the side play between a bent shaft and shaft of the balance weight No. 1 changes at rotation, measure a side play in four designated provisions (see rice. Provisions in which it is necessary to measure a balance weight No. 1 shaft side play in relation to a bent shaft).
5. Turn a bent shaft of the engine on several turns and establish in situation in which the piston of the first cylinder is in the top dead point. Check that tags on assembly of the balance weight were repeatedly combined.
6. Turn a bent shaft of the engine clockwise before combination of a tag of a shaft of the balance weight No. 1 with the index (see rice. Definition of a side play of a shaft of the balance weight No. 1).
7. Install the indicator of hour type on teeths of a gear wheel of a shaft of the balance weight No. 1 (see rice. Installation of the indicator of hour type for measurement of a side play of a shaft of the balance weight). Putting insignificant effort, turn a shaft of the balance weight No. 1 in the parties and define a side play.
8. Remove the indicator of hour type and turn a bent shaft of the engine clockwise until the tag of D on a shaft of the balance weight No. 1 is not combined with the index (see rice. The second and fourth situation for measurement of a side play of a shaft of the balance weight No. 1). Install the indicator of hour type and measure a side play.
9. If the size of a side play differs from the required values, establish laying between assembly of the balance weight and the block of cylinders of the required thickness.