Repair and operation of the Toyota Camry car - 3.8.3. Installation//Toyota Camry of 1992-1997 /

Toyota Camry

1992-1997 of release

Repair and operation of the car



Toyota Camry
+ General data
+ 1. Maintenance
+ 2. Engine
- 3. Six-cylinder V6 engines
   3.2. General information
   3.3. The repair which is not demanding removal of the engine
   + 3.4. Top Dead Point (TDP) of the piston of the first cylinder
   + 3.5. Cover of a head of the block of cylinders
   + 3.6. Inlet collector
   3.7. Final collector
   - 3.8. Gear belt and pulleys
      3.8.2. Check
      3.8.3. Installation
   3.9. Replacement of a forward sealing ring of a bent shaft
   3.10. Replacement of sealing rings of camshafts
   + 3.11. Camshafts and pushers
   + 3.12. Head of the block of cylinders
   + 3.13. Oil pallet
   + 3.14. Oil pump
   3.15. Drive flywheel / plate
   3.16. Replacement of a back sealing ring of a bent shaft
   3.17. Suspension bracket of the power unit
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment



3.8.3. Installation

PERFORMANCE ORDER
1. Check that the tag on a pulley of a bent shaft is combined with a ledge on the case of the oil pump (A) and establish a clamp of a pulley and a bolt (In).
2. Apply the means interfering unscrewing of a bolt on a carving of a bolt of fastening of the lower single pulley, establish the lower single pulley and fix it by a bolt, having tightened a bolt the required moment.
3. Establish a gear belt on a pulley of a bent shaft and the lower single pulley. At the same time combine tags on a gear belt and a pulley of a bent shaft.
4. Establish a guide of a gear belt to a pulley of a bent shaft.
5. Establish the lower casing of a gear belt with laying.
6. Establish a pulley of a driving belt on a bent shaft and fix by a bolt, at the same time hold a bent shaft from a provorachivaniye.
7. Establish the top single pulley and fix it by a bolt, having tightened it the required moment.
8. Install a pulley of a gear belt on the left camshaft, and the adjusting pin of the camshaft has to enter dredging of a pulley. Holding the camshaft from a provorachivaniye a wrench, screw up a bolt of fastening of a pulley of the camshaft.
9. Repeatedly check combination of adjusting tags.
10. Check that an adjusting pin right the distributor the leg of a shaft is above. Otherwise uncover a head of the block of cylinders and a wrench turn the camshaft so that the tag on a pulley of the camshaft was combined with the index on a back casing of a gear belt.
11. Turn a pulley of the left camshaft clockwise on one tooth. Establish a gear belt on a pulley and turn a pulley in a starting position.
12. Install a pulley on the right camshaft. At the same time the adjusting pin of the camshaft has to enter dredging of a pulley.
13. Fix a pulley by a bolt, at the same time a wrench hold the camshaft from a provorachivaniye.
14. Establish a gear belt on a camshaft pulley. If the gear belt is reused, combine earlier made tags.
15. Using a press or a vice, slowly press a pusher of the mechanism of a tension of a gear belt into the case and record it in this situation a steel core, having inserted it through an opening in the case of the mechanism of a tension and pusher.
16. Establish the top casing of a gear belt.
17. Further installation is made in the sequence, the return to removal.