Toyota Camry

1992-1997 of release

Repair and operation of the car



Toyota Camry
+ General data
+ 1. Maintenance
- 2. Engine
   2.2. Operations on repair of the engine on the car
   2.3. Top dead point of the first cylinder
   + 2.4. Cover of a head of the block of cylinders
   + 2.5. Inlet collector
   + 2.6. Final collector
   - 2.7. Gear belt and pulleys
      2.7.2. Survey
      2.7.3. Installation
   2.8. Replacement of a forward sealing ring of a bent shaft
   2.9. Replacement of a sealing ring of the camshaft
   + 2.10. Camshaft and pushers
   + 2.11. Head of the block of cylinders
   + 2.12. Oil pallet
   + 2.13. Oil pump
   + 2.14. Drive flywheel / plate
   2.15. Replacement of a back sealing ring of a bent shaft
   + 2.16. Suspension bracket of the power unit
+ 3. Six-cylinder V6 engines
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
+ 10. Automatic transmission
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment




2.7. Gear belt and pulleys

2.7.1. Removal

GENERAL INFORMATION

Preventions

In the presence in the code radio receiver against theft, before an accumulator detachment, check that you have connection codes.

On models since 1993 the system of the airbag of safety is disconnected if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in a specialized workshop for maintenance of system.


Elements of the drive of the mechanism of gas distribution of the four-cylinder engine
1 – top casing of a gear belt;
2 – camshaft pulley;
3 – single pulley;
4 – spring;
5 – pulley of the oil pump;
6 – single pulley No. 2;
7 – pulley of a bent shaft;
8 – guide of a gear belt;
9 – gear belt;
10 – lower casing of a gear belt;
11 – pulley of a driving belt of a bent shaft

PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
2. Lift a forward part of the car and record on supports. Remove the right forward wheel and a protective arch of a wheel.
3. Merge cooling liquid from the cooling system.
4. Unscrew spark plugs and take off driving belts.
5. Remove the generator together with an arm.
6. Unscrew bolts of fastening of a tank with liquid of the amplifier of steering and the executive mechanism a cruise control and move them aside.
7. Support the engine by a jack through wooden whetstone and remove the right support and draft of a support.
8. Unscrew bolts of fastening of the top casing of a gear belt, move a plait of wires aside and remove the top casing together with laying.
9. Install the piston of the first cylinder in VMT in a compression step, at the same time the small opening in a pulley of the camshaft has to be combined with VMT tag on a bearing cover.
10. If the gear belt is repeatedly established, note its mutual situation in relation to a pulley of the camshaft and the direction of its rotation. 11. Weaken a bolt of fastening of the top single pulley and remove a spring. If it is necessary to make replacement of a sealing ring of the camshaft or to remove a head of the block of cylinders, shift a gear belt from a camshaft pulley, without removing it from a pulley of a bent shaft.

12. If the pulley of the camshaft is worn-out or damaged, uncover a head and, holding from a provorachivaniye the camshaft a big wrench, unscrew a bolt of fastening of a pulley of the camshaft.
13. Record a bent shaft of the engine from a provorachivaniye for teeths of a gear wreath of a flywheel and unscrew a bolt of fastening of a pulley of a bent shaft. 14. Using a stripper or mount, remove a pulley from a bent shaft.
15. Remove the lower casing of a gear belt together with laying and take off a belt from a pulley of a bent shaft.
16. If the gear belt is repeatedly established, note the mutual provision of a belt and a pulley of a bent shaft. 17. Take off a gear belt from a pulley of a bent shaft.
18. If the pulley of a bent shaft is worn-out or damaged, or bypass мо to replace a forward sealing ring of a bent shaft, remove a pulley from a bent shaft.