Toyota Camry

1992-1997 of release

Repair and operation of the car



Toyota Camry
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
+ 10. Automatic transmission
- 11. Coupling and power shafts
   11.2. General information
   + 11.3. Check and replacement of a clutch plate
   + 11.4. Release bearing
   + 11.5. Main cylinder of coupling
   + 11.6. Working cylinder of coupling
   11.7. Removal of air from hydraulic system of coupling
   11.8. Starting switch of coupling
   - 11.9. Hinge of Equal Angular Speeds (HEAS)
      11.9.1. Removal
      11.9.2. Installation
   + 11:10. Replacement of protective covers and repair of hinges of equal angular speeds
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment




11.9.1. Removal

GENERAL INFORMATION

Arrangement of a blooming ring of fastening of the intermediate bearing of the right power shaft

Installation of a temporary bolt instead of a power shaft in a nave of a forward wheel

1 – washer with a diameter of 50 mm;

2 – washer with a diameter of 45 mm;

3 – nut;

4 – bolt


PERFORMANCE ORDER
1. Remove a weight wire from the accumulator.
Preventions

In the presence in the code radio receiver against theft, before a detachment of the accumulator check that you have connection codes.

On models since 1993 the system of the airbag of safety is disconnected if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in a specialized workshop for maintenance of system.


2. Tighten the parking brake.
3. Take the forelock and unscrew a lock-nut of fastening of a power shaft to a nave.
4. Unscrew on several turns a nut of fastening of a power shaft to a nave.
5. Weaken nuts of fastening of a wheel, lift a forward part of the car and record on supports. Remove a wheel. Completely unscrew a nut of fastening of a power shaft to a nave.
6. If the left hinge of a power shaft for replacement of a protective cover on models with engines 3VZ-FE or 1 MZ-FE is removed, weaken 6 bolts of fastening of the internal hinge to a flange of differential or a flange of an intermediate shaft.
7. Unscrew a nut, the fixing steering thirst for a rotary fist and, using a stripper of spherical hinges, remove steering draft from a rotary fist.
8. Unscrew the nuts fixing the lower hinge of a rotary fist to the cross lever and separate the lower lever from the spherical hinge.
9. Take away a nave from the car and take the external end of a power shaft from a nave.
10. If the power shaft densely sits in a nave, temporarily put the clamp of fastening of a nave and, using the hammer, beat out a power shaft from a nave, at the same time tightening a car wheel outside.
11. If you remove the internal hinge of a power shaft from the transmission fixed by a lock ring precede telno merge oil from the transmission.
12. On models with engines 3VZ-FE or 1MZ-FE unscrew 6 bolts of fastening of the internal hinge to a driving flange of the transmission and remove the hinge. If the power shaft is removed for replacement of a sealing ring of differential, take a driving flange from the transmission. For this purpose insert mount between a driving flange and a case of the transmission and when the assistant pulls a power shaft outside, strongly sharp blow to the end of mount beat out a driving flange from gearing in a semi-axial gear wheel of differential.
13. At removal of the internal hinge of the left power shaft on models with engines 5S-FE take a power shaft from the transmission. For this purpose insert mount between the internal hinge and a case of the transmission and when the assistant pulls a power shaft outside, strong sharp blow to the end of mount beat out a power shaft from gearing in a semi-axial gear wheel of differential.

14. For removal of the internal hinge of a power shaft unscrew a bolt of fastening of the intermediate bearing.
15. Remove a blooming ring and sharply pull a power shaft outside. At the same time the power shaft has to leave gearing in a semi-axial gear wheel of differential.
16. At the same time the power shaft has to leave gearing in a semi-axial gear wheel of differential.
17. Do not lower the car on wheels with the removed by two or one power shafts as it will lead a niya of bearings to a povrezhda. If it is necessary to move the car with the removed power shafts, instead of a power shaft in a nave establish a bolt with a nut and two big washers (see rice. Installation of a temporary bolt instead of a power shaft in a nave of a forward wheel).