Toyota Camry

1992-1997 of release

Repair and operation of the car



Toyota Camry
+ General data
+ 1. Maintenance
+ 2. Engine
+ 3. Six-cylinder V6 engines
+ 4. Capital repairs of engines
+ 5. Cooling and heating
+ 6. Fuel system
+ 7. System of ignition
+ 8. Decrease in toxicity
+ 9. Transmission
- 10. Automatic transmission
   10.2. General information
   + 10.3. Diagnostics
   + 10.4. Adjustment and replacement of a cable of the choice of transfers
   10.5. Check and adjustment of a cable of management of a butterfly valve
   + 10.6. Check, replacement and adjustment of the switch of blocking of a starter
   + 10.7. Lock of blocking of the lever of the choice of transfers
   + 10.8. Replacement of sealing rings
   - 10.9. Check and replacement of support of the transmission
      10.9.1. Removal
      10.9.2. Installation
   10:10. Electronic control system
+ 11. Coupling and power shafts
+ 12. Brake system
+ 13. Suspension bracket
+ 14. Body
+ 15. Electric equipment




10.9.1. Removal

GENERAL INFORMATION

Arrangement of bolts of fastening of a protective plate on the four-cylinder engine

Arrangement of bolts of fastening of a protective plate on the six-cylinder engine

PERFORMANCE ORDER
1. Remove a cowl.
2. Take off pressure in fuel system.
3. Remove a weight wire from the accumulator.
Preventions

In the presence in the code radio receiver against theft, before a detachment of the accumulator check that you have connection codes.

On models since 1993 the system of the airbag of safety is disconnected if the accumulator is disconnected for long term. If a control lamp of a safety cushion it lights up and necessary to burn after repeated connection of the accumulator, it is necessary to address in a specialized workshop for maintenance of system.


4. Disconnect the electric socket and remove the executive mechanism a cruise control.
5. Remove the accumulator and a support of the accumulator.
6. Remove an air inlet and a casing of the air filter. Disconnect fuel-supply lines from the engine and close them traffic jams.
7. Remove the fuel filter and an arm of the fuel filter.
8. Remove a charcoal canister together with an arm.
9. Remove a washer reservoir of a windshield and a broad tank.
10. Disconnect an accelerator cable from a control lever a butterfly valve.
11. Mark and disconnect all vacuum hoses, hoses of cooling liquid, electric sockets and tires of grounding.
12. Remove the fan of a radiator and a casing of the fan. Merge cooling liquid from the cooling system, remove a radiator and disconnect hoses from a heater.
13. Disconnect a cable of the choice of transfers from the lever of the choice of transfers.
14. Lift the car and record on supports. Remove wheels.
15. Disconnect a reception exhaust pipe from a final collector.
16. Remove mudguards.
17. Merge engine oil.
18. Take off driving belts.
19. Merge oil from the transmission.
20. Disconnect hinges of power shafts from the transmission.
21. On models with the amplifier of steering unscrew bolts of fastening of the pump of the amplifier of steering and move the pump aside, without disconnecting from it hoses.
22. On models with the air conditioning system unscrew bolts of fastening of the compressor of the conditioner and move it aside, without disconnecting from it hoses.
23. Disconnect hoses from the oil heater of the transmission and immediately close them traffic jams. On models with four-cylinder engines remove an oil filter and the oil heater. For access to a drive plate гидротран a sformator unscrew bolts and remove a protective plate (see rice. An arrangement of bolts of fastening of a protective plate on the four-cylinder engine and rice. An arrangement of bolts of fastening of a protective plate on the six-cylinder engine). Unscrew 6 bolts of fastening of a plate of the drive to the hydrotransformer, at the same time for access to bolts of fastening turn a bent shaft.
24. Hook on the engine together with the transmission cargo rise by the ny mechanism and raise so that the weight of the engine was perceived by the load-lifting mechanism.
25. Unscrew bolts of fastening of support of the power unit.
26. Being careful, slowly take the engine together with the transmission from a motor compartment of the car.
27. Lower the power unit on wooden whetstones and establish so that under the transmission it was possible to establish a jack.
28. Remove a starter.
29. Supporting the transmission by a jack, unscrew bolts of fastening of the transmission to the engine.
30. Move the transmission from the engine and remove it. At the same time be careful that the hydrotransformer was not removed from an entrance shaft of the transmission.
31. Remove the hydrotransformer from an entrance shaft of the transmission.